06-05-2019 09:25 AM
Hi,
i want to add a thermocouple to an AI at my PXI System.
It is a thermocouple typ T and now my Question is, which value do i have to set at CJC Value and what is the sense of this value?
Best wishes
Ache
Solved! Go to Solution.
06-06-2019 01:37 AM
First you need to know how a thermocouple (TC) works
https://en.wikipedia.org/wiki/Thermocouple
Since the TC only can measure a temperature difference between two points ,the sensing point and the so called Cold Junction Compensation point , you need on known that CJC temperature.
Usually the voltages generated are quite small, so what type of AI do you have?
06-06-2019 01:50 AM
Hallo Henrik,
dann können wir eigentlich auch auf deutsch weiter schreiben... 😉
Ok, also muss man die Raumtemperatur wissen und ein TC auf Raumtemperatur legen damit man mit einem 2. messen kann?
Ich habe ein TC Messmodul (PXIe-4353).
LG,
Ache
06-06-2019 02:29 AM - last edited on 01-11-2024 11:23 PM by migration-bot
Hi Ache,
which module/card would you like to use for thermocouple measurements?
Our PXI-based temperature measurement moduls can be found here:
https://www.ni.com/en-us/shop/category/temperature.html?productId=118784
The PXIe-4353 would be an appropriate solution:
https://www.ni.com/docs/en-US/bundle/pxie-4353-specs/resource/375508c.pdf
The card includes CJC-compensation.
Where do you want to set the CJC-value? In LabVIEW?
Best Regards,
NI TSE
06-06-2019 02:35 AM
Hi,
I have the PXIe-4353 but no adapter yet.(it is ordered already)
Now i wanted to test it with another module(PXIe-6356).
What can i do now without an included CJC?
No, i am using VeriStand.
Thank you very much!
Ache
06-06-2019 03:38 AM - last edited on 01-11-2024 11:24 PM by migration-bot
Hallo Ache,
das Problem mit der TC-Messung durch 6356 ist folgendes:
Auch im +/-1 V Messbereich sollst du mit 61 uVrms<->1.4°Crms rechnen, 30 uV offset<->0.7°C offset.
Zusätzlich ohne CJC misst du nur DeltaT=Tactual-Tref. Die ganze Unsicherheit in der Schatzung von Tref wird den Messfehler steigern.
"Type-T thermocouples have a sensitivity of about 43 µV/°C."
https://en.wikipedia.org/wiki/Thermocouple
https://www.ni.com/docs/en-US/bundle/pxie-usb-6356-specs/page/specs.html
Zum Beispiel du misst 4.3 mV, was ca. 100°C Temperaturunterschied entspricht, aber es beinhaltet schon ca. 2°C Messfehler.
https://www.thermocoupleinfo.com/type-t-thermocouple.htm
Was ist dann die aktuelle Temperatur? Tactual=Tref+(100+/-2)°C, deshalb wird der Schätzungsfehler des Trefs als Messfehler zum Messergebnis addiert. Tref hängt davon ab, wie warm die Anschlüsse sind, infolgedessen verschiebt es sich typisch 10-15°C mit der Zeit dank der Selbsterwärmung der Karte nach dem Einschalten.
Viele Grüße,
NI TSE
06-06-2019 04:27 AM
Hallo,
Vielen Dank, das hört sich alles plausibel an!
Heißt dann das, dass ich mit der PXIe-6356 (oder auch 6378, welche ich auch noch zur Verfügung habe) lieber keine TC-Messungen machen sollte und lieber auf den Adapter für PXIe-4353 warten sollte?
Ist dann bei der 4353 das Problem mit der Erwärmung der Karte nicht auch da?
VG,
Ache
06-06-2019 04:38 AM
Hallo,
genau.
Die Erwärmung ist da, aber es wird durch CJC in situ kompensiert.
(Tref wird kontinuierlich gemessen und zu DT addiert.)
Grüße,
NI TSE
06-06-2019 04:47 AM
Hallo,
Vielen Dank, dann warte ich auf den Adapter.
LG
Ache