Cable Pinouts

[_Dmitri_]

Hello,

   I am looking for pinout's and color code by pair for the following cables: 782417-03 and 779038-02. I need to confirm which wires inside are which color and connect to which pin on either end. Also to see if/how they are grouped and/or twisted. I am running from one PXI card to another, then to a switch card and back out to a DUT Tx and Rx. I need to know if I can use these cables, or if I have to just order the connectors and do my own discrete wiring. Thank you.

[mtillman]

Hi,

I have attached a few links that should help provide a bit more information for the cables. The first cable did not have any pinouts available, however, I was able to find some information on compatible PXI cards. As for the second cable, I think that you are looking for the LFH200 information so those are included below.

782417-03 Cable Info: http://sine.ni.com/nips/cds/view/p/lang/en/nid/212026

779038-02 (LFH200 Dimensional Drawing and Cable Installation):

http://www.ni.com/en-us/support/documentation/dimensional-drawings/model.lfh200.html

http://www.ni.com/pdf/manuals/373848f.pdf

Hopefully this helps!

Megan T.

Technical Support Engineer

National Instruments

[_Dmitri_]

Hi Megan,

   That was perfect for the 200-pin. Another NI person sent me some additional info on the 160, so I now have the pin-out of which d-sub ends up with which pins from the other end, but still need to know whether or not the wires inside are twisted pairs or not. Can I assume that the colors on the flying lead cable are the same as the (4) 50-pin d-sub cable? The two PXI cards I am using this cable with are the 2526 and the 2576.

Best Regards,

Kris

[mtillman]

Hey Kris, 

I looked into the 160 pin cable and it seems like the wires inside are not twisted pairs. As for the colors, they should be the same.

I did a little digging into the compatibility for the PXI cards and the cables and this is what I found:

160 pin should support the following:

• NI PXI-2510 
• NI PXI-2520/1/2/3 
• NI PXIe-2524/5/6 
• NI PXIe-2737/8/9 

200 pin should support the following depending on the configuration used:

• SH200LFH-4xDB50F-C—Recommended for use with the PXI-2569/2570/2571 or SCXI-1169.
• SH200LFH-4xDB50F-S—Recommended for use with the PXI-2575 or SCXI-1175.
• SH200LFH-BARE WIRE—Recommended for termination other than 50-pin female D-SUB.
  

Best, 

Megan T.

Technical Support Engineer

National Instruments

[_Dmitri_]

Hi Megan,

   Thanks for the info, I have one more cable, I missed it earlier, your latest reply got me to find the error on my end. For the 2576 card, I need to use p/n 780009-01. Can you send me the pin out of each end and pairing/color scheme for that as well?

Best

Kris

[mtillman]

Hey Kris,

Attached is the installation instructions for the LPH 160 cable (Part Number: 780009-01). Hopefully this is what you were looking for!

Installation Instructions LFH160 Cable

http://www.ni.com/pdf/manuals/374694b.pdf

Best,

Megan T.

Technical Support Engineer

National Instruments

[_Dmitri_]

Hey Megan,

   That is a great help, last question, are they twisted pairs or no? I am assuming no.

[mtillman]

Hey Kris, 

I couldn't find any information verifying it was twisted pair so I would assume not.

Best, 

Megan T.

Technical Support Engineer

National Instruments