Multisim and Ultiboard

cancel
Showing results for 
Search instead for 
Did you mean: 

Something everyone can use....and it's free

Hi I am new to this forum, but recently I tried to build cuircuit with LM3914 using Multisim 10 and the Spice model for this component was not available in the database.

 

I did a bit of the recearch and found that "Kittmaster" was able to implement it.   Is it possible to make this model available for download. 

0 Kudos
Message 41 of 55
(3,767 Views)
I've never finished the model and there were some parametric issues.  I don't think it would be of any use to anyone.


Signature: Looking for a footprint, component, model? Might be here > http://ni.kittmaster.com
0 Kudos
Message 42 of 55
(3,749 Views)

Thanks,

 

I guess I am out luck, on this one.

 

 

David

0 Kudos
Message 43 of 55
(3,739 Views)

Chris:

 

It is October 2, 2017 in the USA and I know you re-vamped your site..

 

I can not get into the REGISTER place on your site...

 

Got a link to the REGISTER...  Even using Incognito I can not get it.. Can not even git in Safari...

 

Anyway, EXCITED to see your latest creation!

 

 

0 Kudos
Message 44 of 55
(1,909 Views)

Site has been re-opened for a limited time. Personal tragedy has crossed my families doorstep, it will be open for a short time and temporarily closed again until we recover.

 

Thank you

Chris



Signature: Looking for a footprint, component, model? Might be here > http://ni.kittmaster.com
0 Kudos
Message 45 of 55
(1,904 Views)

Chris:

 

Sorry to hear about the personal tragedy!

 

And, thanks for allowing us to sign on... I did so but my dave@TacticalFlowMeter.com email died just when you would have sent a confirmation.. Go figure..

 

I will wait till you get things in order with the family. I have a very cool footprint to share. It is for a really nasty Bluetooth Module footprint that was a pisser to lay out.

 

I am also searching for folks who want to lay out boards using Ultiboard and Multisim...

0 Kudos
Message 46 of 55
(1,895 Views)

Thanks, it's been a hard few months. 

 

I could enter you in the system, need a username.

 

I still use the software, but I've been using pads over the last 8 years. I think its a great idea.

 

I'll believe you can upload your footprints and boards into the system when your registered. Give it a shot when your account is set up, if not, I'll take a look. 

 

No zips, rars, exes or anything like that will be allowed to upload, but it will allow NI file extensions as I believe I have upload filters active to accept people parts for those that what to contribute.

 

Best,

Chris



Signature: Looking for a footprint, component, model? Might be here > http://ni.kittmaster.com
0 Kudos
Message 47 of 55
(1,893 Views)

"I am also searching for folks who want to lay out boards using Ultiboard and Multisim..."

 

What are you searching for folks to do?  I've been doing circuit designs and layouts with MS/UB for about 20 years.

0 Kudos
Message 48 of 55
(1,849 Views)

Hello, I can't seem to find kittmaster's email to get access to kittmaster. I'm trying to find a component not available in master database. The component is IC 565. Hope you could help me. Thank you.

0 Kudos
Message 49 of 55
(1,534 Views)

The information you seek is all spelled out specifically from the home page and where to go to find the email. Read the article and you will understand.



Signature: Looking for a footprint, component, model? Might be here > http://ni.kittmaster.com
0 Kudos
Message 50 of 55
(1,530 Views)