LabVIEW

cancel
Showing results for 
Search instead for 
Did you mean: 
Reply

Reading a diode resistance by NI USB vs by Multimeter

Solved!
Go to solution
Highlighted

Hello, 

I am reading a resistance of diode at certain voltage input from power supply 

and I found that 

 

at 0.2 V

the resistance value by NI USB-6212 : 200 ohm

the resistance value by multimeter: 2 kohm

at 0.5 V

the resistance value by NI USB-6212: 500 ohm

the resistance value by multimeter: 5 kohm.

 

Would you please let me know why the values are different by 10 times?

Thanks.

 

 

0 Kudos
Message 1 of 7
(1,147 Views)

If you don't want to endure the wrath of a certain Bob, you best post more information and code.

 

Me....I'm going to run and hide.  Smiley Very Happy

aputman
LabVIEW 2017
LabVIEW Programming
0 Kudos
Message 2 of 7
(1,138 Views)

You set something up wrong?  You used the mutlimeter wrong?

 

None of those numbers sound right to me.  But we really can't help you since you didn't provide us any information or code such as the VI you used to measure with the USB-6212.

0 Kudos
Message 3 of 7
(1,135 Views)

Hi nohmoses,

 

how do you measure resistance using a simple USB6212? This box can only measure voltages…

 

How does your multimeter measure resistance? Which type of DMM do you use? What's the specified accuracy of this DMM?

 

Clarify all those questions and we are on a way to solve this problem!

Best regards,
GerdW
CLAD expired, using 2009SP1 + LV2011SP1 + LV2017 (+LV2018 sometimes) on Win7+cRIO
Kudos are welcome Smiley Wink

0 Kudos
Message 4 of 7
(1,125 Views)

Resistance is typically not measured while the circuit is live.

 

-AK2DM

~~~~~~~~~~~~~~~~~~~~~~~~~~
"It’s the questions that drive us.”
~~~~~~~~~~~~~~~~~~~~~~~~~~
0 Kudos
Message 5 of 7
(1,115 Views)

Hello, 

Simplely, I connected the NI board or multimeter as attached the figure "Picture1" to a LED

and monitored its resistance change.

In the block diagram, I chose the AI Input -> Resistance. 

The DMM is Fluke 287.

Please let me know if you have any questions.

Thanks. 

0 Kudos
Message 6 of 7
(1,104 Views)
Solution
Accepted by topic author nohmoses
10-05-2016 10:39 AM

No - you cannot measure resistance that way.

 

To measure resistance, you normally pass a known current and then measure the voltage. A DMM will do this by generating a small known current and measuring the voltage internally. If you are supplying an external voltage as well, the DMMs internal resistance measurement will not work.

 

For the LabVIEW - the USB-6212 can only measure voltages. If you want to measure the resistance while the device is powered, you will need know/measure both the current (e.g. through a shunt resistor) and the voltage and then do R = V/I to get the resistance. I'm not sure what the 6212 does if you try to take a 'resistance' measurement as it doesn't have an internal current source.

 

Oh, I thought this all sounded familiar - here's a similar thread: https://forums.ni.com/t5/LabVIEW/daqmx-resistance-measurement-6251/td-p/3267084



Certified LabVIEW Architect (CLA), Certified LabVIEW Embedded Systems Developer (CLED) and Certified TestStand Developer (CTD)
MediaMongrels Ltd. - NI Alliance Partner | GDevCon :: 21-22nd August 2019 :: Birmingham, UK
0 Kudos
Message 7 of 7
(1,097 Views)