I want to EtherCAT Master using Beckhoff C6015-0010 (C9900-C583)

[-max-]

Hi,

I have a Beckhoff C6015-0010 (with C9900-C583).

This pc is ultra compact industrial PC with ethernet 2 ports.

I installed NI Real-Time Desktop PC in this.

It worked on RTos very well with LabVIEW. (targer searching, debug, deploy)

But RTos can not work when I set network option to EtherCAT (2nd ethernet port) in MAX.

I can not find RT target in MAX. and project in LabVIEW.

How can I work EtherCAT Master in this pc?

Please help me.

*additional infomation

LabVIEW 2015 sp1 (RT module)

Device driver Feb.2016

Beckhoff Ethernet chip : Intel I210 Gigabit

[Yin_W · Accepted solution]

Hello,

NI EtherCAT master only supports the following hardware. Can you please have a check?

EtherCAT Master	Earliest Supported Version
cRIO-9074	1.0
PXI-8106	1.0
PXIe-8130	1.0
PXI-8104	1.0
PXI-8183	1.0
PXI-8145	1.0
cRIO-9022	1.01
PXI-8108	1.01
cRIO-9024	1.1
NI 3100	1.1
NI 3110	1.1
cRIO-9023	1.2
cRIO-9025	1.2
NI 9792	1.2
EVS 1463RT	1.2
EVS 1464RT	1.2
All real-time embedded PXI controllers with the PXI-8231 or PXI-8232 Ethernet interface	2.0
PXIe-8133	2.0
PCI-8232	2.0
PCIe-8231	2.0
PCIe-8233	2.0
PCIe-8235	2.0
cRIO-9081	2.2
cRIO-9082	2.2
RMC-8354RT	2.5
RMC-8355RT	2.5
PXI-8109	2.5
PXI-8115	2.5
PXIe-8115	2.5
PXIe-8135	2.5
cRIO-9068	2.6
cRIO-9030	14.0
cRIO-9031	14.0
cRIO-9033	14.0
cRIO-9067	14.0
sbRIO-9651	14.0
cDAQ-9132RT	14.0
cDAQ-9134RT	14.0
cDAQ-9139RT	14.0
PXI-8840	14.0
PXIe-8840	14.0
CVS-1457RT	14.0
PXI-8119	14.0
PXIe-8119	14.0
PXIe-8880	14.0
cRIO-9035	14.5
cRIO-9036	14.5
cRIO-9038	14.5
cRIO-9039	14.5
cRIO-9064	14.5
cRIO-9065	14.5
cDAQ-9133RT	14.5
cDAQ-9135RT	14.5
sbRIO-9607	15.0
sbRIO-9627	15.0
cDAQ-9136RT	15.0
cDAQ-9137RT	15.0
CVS-1458RT	15.0
cRIO-9032	16.0
cRIO-9037	16.0
cRIO-9035 (Sync)	16.0
cRIO-9039 (Sync)	16.0
IC-3171	16.0
IC-3172	16.0
IC-3173	16.0
cRIO-904x	17.6

[-max-]

Oh..... Thank you very much.......

I found additional infomation in "INSTALLATION GUIDE NI-Industrial Communications for EtherCAT®"

http://www.ni.com/pdf/manuals/372624f.pdf

According to this document,

"By default, some real-time controllers, such as Real-Time Desktop controllers, do not have the special Ethernet adapter to access the EtherCAT network. Refer to the list of supported hardware in the NI-Industrial Communications for EtherCAT Readme for more information about the additional adapters that you can add."