Hobbyist Toolkit

cancel
Showing results for 
Search instead for 
Did you mean: 

Arduino Max6675 Labview Linx Interface

Hello World! 🙂

this is Nino. First of all thanks for accepting me in this community!

I am trying to read the temperature of a K-thermocouple interfaced with a MAX6675 SPI, using Arduino and Labview.

However, I could not find any information / tutorial on how to make this project working and I have no Idea on how to do this.

I am using:

  1. labview 2019 64bit with the last version of LINX and VISA drivers
  2. Arduino Uno Rev 3
  3. MAX6675, K-type thermocouple

My MAX6675 is connected with the following PINs

  • SCK 10
  • CS 9
  • SO 8

Could you, please, post a working VI for this project or Post some instructions I can refer to?

Thanks in advance for reading my post and for your kindness

Cheers

Nino

0 Kudos
Message 1 of 9
(1,027 Views)

Could you also send me a working  LabVIEWInterface.ino, configured for reading the MAX6675 shield, please?

0 Kudos
Message 2 of 9
(973 Views)

Hello!

 

Unfortunatelly i do not have this solution made yet.

 

However there is an example of linx communication with arduino usint the PmodTC1 in the examples folder called LINX -PmodTC1.vi

 

the PmodTC1 also uses maximintegrated IC, but the MAX31855 instead of MAX6675.

 

I believe that with some of non work arounds you may be able to change that code to fit your needs.

 

 

 

Jorge Augusto Pessatto Mondadori, PhD
Sistema Fiep
CLAD, CLD
0 Kudos
Message 3 of 9
(951 Views)

Thanks a lot, that was very helpful ! 🙂

Something I did not get is this:

To use the MAX31855 with PmodTC1 VI it is still necessary to modify the LIFA BAse?

Does it work just with the original LINX LIFA?

 

0 Kudos
Message 4 of 9
(945 Views)

I tried out yesterday with another SPI chip, just changed the subvi parameters to set clock mode and channel, worked ok. 
now i believe that you don't need LIFA anymore, since it has been substituted by LINX officially.

Jorge Augusto Pessatto Mondadori, PhD
Sistema Fiep
CLAD, CLD
0 Kudos
Message 5 of 9
(901 Views)

Could you send me your vi and explain which parameters should be changed, please? I'd just like to try ho it works.. 

Thanks for your time, I appreciate it very much

Cheers

 

 

 

0 Kudos
Message 6 of 9
(888 Views)

Heyy Nino,
I was also searching for the same. If you found the answer, please share it with me also.

In the meantime what I did to make it work is, I uploaded the Arduino sketch for reading the temperature using the Arduino app and serial printed the temperature value. After that, I acquired the value in LabVIEW using a serial read from Arduino. And it worked well.

Just let me know if you require the Arduino sketch and LabVIEW vi.

Thank you
Ashq

Message 7 of 9
(773 Views)

actually i modify the pmod TC1.vi  and can read the temperature of max 6675 but i have  problem because i think i  have a error at the temperature convert 

now i try to check the temperature with an other instrument to verify the data

0 Kudos
Message 8 of 9
(271 Views)

actualy i am working on this vi 

i have to check the temperature to verify that is correct but i think is ok 

if anybody see a error please tell me

0 Kudos
Message 9 of 9
(261 Views)