Digital I/O

New solutions

Subject

Author

Help using the PXI-6515 for negative voltage controlled logic devices.

uldaq not work for usb-6008 but usb-201

请问USB-6000的PFI端口的TTL高电平是多少？

Pinout for USB-8452 connector

ubuntu 22.04.2 support for NI-DAQMX with nidaqmx on python3

Show: - -

How to control heater switch through labview&PCI-6503

by on Latest post on by

1 Reply 2910 Views

0 Kudos

1 Reply

2New

can digital I/O lines emulate a parallel port?

by on Latest post on by

2 Replies 3136 Views

0 Kudos

2 Replies

3New

Can I get more than 2 StartTrig and 2 REQ inputs from a PCI 6534 card ?

by on Latest post on by

1 Reply 2793 Views

0 Kudos

1 Reply

2New

Can I do 8 bit change detection on port 1 or 3 of the pci-6534?

by on Latest post on by

1 Reply 2897 Views

0 Kudos

1 Reply

2New

Can PCI-6534 multitask unstrobed and pattern I/O functions in separate halves of the same signal group?

by on Latest post on by

2 Replies 3138 Views

1 Kudo

2 Replies

3New

How can I switch off HP34401A Multimeters Display for faster readings"

by on Latest post on by

1 Reply 2818 Views

0 Kudos

1 Reply

2New

Finite Number of Data Points using DIO-32

by on Latest post on by

1 Reply 2859 Views

0 Kudos

1 Reply

2New

Is SingleWrite() still supported ?

by on Latest post on by

1 Reply 2740 Views

1 Kudo

1 Reply

2New

Using RTSI Control with 6534

by on Latest post on by

2 Replies 3275 Views

0 Kudos

2 Replies

3New

My program uses digital i/o port to write four lines separately, and when another program is running, my program goes extremely slow. Why?

by on Latest post on by

3 Replies 3183 Views

0 Kudos

3 Replies

4New

simultaneous digital i/o with a dio-32hs

by on Latest post on by

1 Reply 2908 Views

0 Kudos

1 Reply

2New

Configure PCI-DIO-32HS card

by on Latest post on by

1 Reply 2946 Views

0 Kudos

1 Reply

2New

Can I use the output of the PC-TIO card to drive 5V into a 50 ohm load?

by on Latest post on by

1 Reply 2937 Views

1 Kudo

1 Reply

2New

Why are my digital ports always displaying a high state in example vi's and in MAX(red led lights up)?

by on Latest post on by

1 Reply 2988 Views

0 Kudos

1 Reply

2New

for NI-6534 PCI, does the internal clock send one 8-bit word, for one port, at the clock's Hi to Lo transition, Lo-hi, any at transition at all or neither?

by on Latest post on by

1 Reply 2947 Views

0 Kudos

1 Reply

2New

What is a 182097-01 board?

by on Latest post on by

1 Reply 3479 Views

0 Kudos

1 Reply

2New

non-repetitive Pattern generation PCI-6534, LABVIEW 6.0, no trigger, no handshake, serial bit stream output to one LINE, each bit outputed with board's internal clock

by on Latest post on by

1 Reply 2988 Views

0 Kudos

1 Reply

2New

non-repetive Pattern generation PCI-6534,LABVIEW 6.0, no trigger, no handshake, serial bit stream output to one channel, each bit outputed with board's internal clock

by on Latest post on by

1 Reply 3228 Views

0 Kudos

1 Reply

2New

how to do continuous pattern output from buffer

by on Latest post on by

2 Replies 3211 Views

0 Kudos

2 Replies

3New

"Buffered Pattern Output Vi", If I call DIO config and DIO write, how do I configure these so that they know to output to a single, specified line (ex., DIOAO) and how do I give to WRITE the appropriate array, each element of which is "1" or "O"?

by on Latest post on by

1 Reply 2915 Views

0 Kudos

1 Reply

2New

group writing to 6508

by on Latest post on by

2 Replies 3201 Views

2 Kudos

2 Replies

3New

Why does my NIDAQ application behave correctly on a P233 WinNT 4.0sp6 system and incorrectly on a P3-600 Win NT 4.0sp6?

by on Latest post on by

3 Replies 3093 Views

1 Kudo

3 Replies

4New

How do I locate the base addresses of the 2 PC-DIO-24pnp boards I've installed?

by on Latest post on by

1 Reply 2893 Views

0 Kudos

1 Reply

2New

I am using a PCI 6534 for pattern output. I only seem to be able to trigger a pattern many times if I rewrite the buffer each time.However I want to write to the buffer once and then output a pattern whenever I trigger the card.

by on Latest post on by

2 Replies 3190 Views

0 Kudos

2 Replies

3New

Signal distortion when using NI Scope 5122 with Mux. Switch 2503 2-wire config. to adquire a signal of 16 impulses. Any recomendations?

by on Latest post on by

1 Reply 3099 Views

1 Kudo

1 Reply

2New

How do I create an interrupt on the PCI-DIO-96 from an external signal connected to the lines PC0 or PC3 of a port?

by on Latest post on by

1 Reply 3266 Views

0 Kudos

1 Reply

2New

Why does my PCI6534 keep missing triggers?

by on Latest post on by

1 Reply 3042 Views

0 Kudos

1 Reply

2New

Please recommend IO Mapped Digital IO Card

by on Latest post on by

1 Reply 3092 Views

0 Kudos

1 Reply

2New

Problem with the Continious Pattern Input VI (from the 653x library) running on a PCI DIO 6534 card.

by on Latest post on by

1 Reply 3140 Views

0 Kudos

1 Reply

2New

How to avoid underFlowError error (code 10843)?

by on Latest post on by

1 Reply 3048 Views

0 Kudos

1 Reply

2New

What do you need our team of experts to assist you with?

Request a quote Find the right product Place an order Get support on a product

How can we help?

Please enter your information below and we'll be intouch soon.

This field is required

Preferred communication method

Email Phone call

What do you need our team of experts to assist you with?

Request a quote Find the right product Place an order Get support on a product