Wireless Sensor Networks

cancel
Showing results for 
Search instead for 
Did you mean: 

Using outputs in WSN-3202

Good morning,
I have a doubt. You are aware that the sensor WSN-3202 has 4 analog inputs and4 digital outputsa doubt arises in respect of this sensor outputs.
For example, for connecting a LED (6V) to one of the outputs of the sensor, I have to do?
Best regards,
Hugo Santos
 
 
 

 

Hugo Santos
Student at ISEC - Master Mechanical Equipment and Systems
0 Kudos
Message 1 of 18
(6,523 Views)

Mr Santos,

 

Are-you asking how to wire a LED to the WSN-3202 ? Relying on the manual, you have to wire it to pins 9 and 10 for instance. Be sure that the module is configured as you wish (in the project explorer, right-click on the module and select properties).

Pay attention to the tension, the output is 12V.

 

Regards,

 

Mathieu P. | Certified LabVIEW Associate Developer
National Instruments France


Journées techniques : des fondamentaux aux dernières technologies pour la mesure et le contrôle/comm...

0 Kudos
Message 2 of 18
(6,512 Views)

Good morning,
for programming in LabView plates WSN, I need to have LabVIEW WirelessSensor Network Module Pioneer?
For example, I need to have input and output, can do the way is down?
regards,
Hugo

Hugo Santos
Student at ISEC - Master Mechanical Equipment and Systems
0 Kudos
Message 3 of 18
(6,496 Views)

Hello,

 

If you want to programm WSN nodes, you need the Module NI LabVIEW Wireless Sensor Network (WSN) Pioneer. If you just want to read data from nodes, without programming them, you can just install the WSN drivers.

 

I don't understand your second question. If you need help for starting with WSN, please look here.

 

Regards,

Mathieu P. | Certified LabVIEW Associate Developer
National Instruments France


Journées techniques : des fondamentaux aux dernières technologies pour la mesure et le contrôle/comm...

0 Kudos
Message 4 of 18
(6,490 Views)

Thanks for reply.

I want read and write with node WSN 3202. I need de LabVIEW Wireless Sensor Network Module Pioneer?

Regards,

Hugo

Hugo Santos
Student at ISEC - Master Mechanical Equipment and Systems
0 Kudos
Message 5 of 18
(6,487 Views)

Hello,

 

If you just want to do that, you don't need the module.

 

Regards,

Mathieu P. | Certified LabVIEW Associate Developer
National Instruments France


Journées techniques : des fondamentaux aux dernières technologies pour la mesure et le contrôle/comm...

0 Kudos
Message 6 of 18
(6,485 Views)

So to get in an output voltage value, I'll have to do?

Regards,

Hugo

Hugo Santos
Student at ISEC - Master Mechanical Equipment and Systems
0 Kudos
Message 7 of 18
(6,483 Views)

Can you tell me exactly what you need ?

 

If you want to set an ouput voltage value, it's impossible. The only outputs avaliable on this node are digital outputs. When you set it to True, the output voltage is 12V.

 

Is that what you need ?

 

Regards,

Mathieu P. | Certified LabVIEW Associate Developer
National Instruments France


Journées techniques : des fondamentaux aux dernières technologies pour la mesure et le contrôle/comm...

0 Kudos
Message 8 of 18
(6,480 Views)

I needed a hardware trigger voltage of 24Vdc, it is possible?
Regards,

 

Hugo

Hugo Santos
Student at ISEC - Master Mechanical Equipment and Systems
0 Kudos
Message 9 of 18
(6,477 Views)

No, it's impossible. Moreover, do not think of using two outputs in series connection. Grounds are internally linked so if you do that, you will do a short.

 

Regards

Mathieu P. | Certified LabVIEW Associate Developer
National Instruments France


Journées techniques : des fondamentaux aux dernières technologies pour la mesure et le contrôle/comm...

0 Kudos
Message 10 of 18
(6,475 Views)