
You are here:	NI Home > NI Developer Zone > NI Discussion Forums

Signal Conditioning

Show: - -

Subject	Replies	Author	Latest Post
Can a Lab-PC+ I/O board be used with SCXI equipment?	1	uwyo_student	‎10-03-2002 10:17 AM by Filipe A.
How do I enter the device numbers/channels in my vi?	1	SKristoff	‎09-30-2002 04:02 PM by AVR
which of single ended referenced & non-referenced is better in cutting crosstalk	3	shantaram	‎10-14-2002 09:51 AM by <Mike Ross&…
Configuring a SCXI-1125 module for use with LabVIEW	1	rockodilered	‎09-18-2002 01:35 PM by Russell
Connection of drain shield to scxi 1321	1	herman 277	‎09-16-2002 01:51 PM by Filipe A.
Can I configure a voltage divider on a SCXI-1100 card in order to read a 24V DC signal without external circuitry?	1	Pascal_ACTIA	‎09-12-2002 09:40 AM by Filipe A.
looking for a sensor to check the water level in a bathtub and send one type of pulse for higher and a different for lower water levels...any ideas?	2	magdalen	‎09-10-2002 08:32 AM by AVR
How can I configure SCXI-1180 to SCXI-1000 chassis	4	aliko	‎09-04-2002 09:53 AM by Filipe A.
What can cause the errors in temperature measurement with SCXI1102 and SCXI1180	2	aliko	‎09-04-2002 09:09 AM by Filipe A.
SCXI-1102 virtual channel reads OK but SCXI temp scan.vi does not	1	Drew	‎09-04-2002 02:23 PM by GerardoG
Can I connect Endevco's 7265A-HS Model Peizoresistive Accelerometer to the NI-4472 directly without any Signal Conditioning hardware?	1	Geeth	‎12-16-2002 10:32 AM by Scorpion
accelerometers	3	saradhi	‎08-26-2002 10:51 AM by Filipe A.
What is the current limit in amperes of the scxi1520 inputs?	3	atrel	‎08-21-2002 01:03 PM by AndrewM
SCXI-1122 Thermocouple System	1	oj	‎08-20-2002 10:01 AM by Filipe A.
Measure negative voltage with SCXI-1121/1321 Combination	1	rehbein	‎08-20-2002 06:37 PM by Patrick R.
SCXI-1200 in SCXI-2000 with won't test using serial cable??	2	Mdlggr	‎08-20-2002 01:17 PM by Mdlggr
Decrease in speed when I plug in SCXI Chassis	2	nnugent	‎08-11-2002 05:29 AM by nnugent
cant access scxi 1163r in labview	1	hendra	‎08-09-2002 02:14 PM by russellb
Is it possible for the SCXI-1530 module to block any of its four channels?	2	lortiz	‎08-07-2002 10:35 PM by lortiz
How to reversible tie up pins in FT01 ??	1	Wolters	‎08-06-2002 09:36 AM by Filipe A.
Has anyone used an 1104C to measure an AC voltage? If so, how?	1	TC_programmer	‎08-02-2002 07:35 AM by Ben
how to configure SCXI 1120 module for 4-20 mA signal	2	bjka	‎08-01-2002 08:44 AM by Filipe A.
what is autocorrelation time with respect to Data Acquisation System	1	Suresh thangap…	‎07-30-2002 09:21 AM by Filipe A.
What NI product can I use for my application?	2	Lina	‎07-29-2002 10:53 AM by Filipe A.
Can not get analog input with SCC-SG04	2	AJ	‎07-26-2002 10:59 AM by AJ
Communication problem with SCXI 1000 Chasis	1	H-1NF_FIR	‎07-25-2002 10:12 AM by Filipe A.
Does a Watlow 96 need a modbus card or is it able to be directly hooked up with a RS232 cable?	2	gwong	‎10-11-2002 04:46 PM by John Munnerlyn
Max 2.2 causes memory dump on dell pc	3	davidsod	‎10-20-2002 05:54 PM by davidsod
Can I use an SCXI-1121 module with 4-20ma signal sources	3	rehbein	‎08-21-2002 08:12 AM by ole
How do I connect an angular speed proximity transducer to my 5B45 module?	2	MihaiTiron	‎07-24-2002 12:10 PM by Sastry V.