Multisim and Ultiboard Idea Exchange

Community Browser
About Multisim and Ultiboard Idea Exchange
Do you have an idea for how to improve Multisim and Ultiboard? Submit and vote on ideas now!

  1. Browse by label or search in the Multisim and Ultiboard Idea Exchange to see if your idea has previously been submitted. If it has, be sure to vote for the idea by giving it kudos to indicate your approval!
  2. If your idea has not been submitted click the New Idea button to submit a product idea. Be sure to submit a separate post for each idea.
  3. Watch as the community gives your idea kudos and adds their input.
  4. As NI R&D considers the idea, they will change its status.
  5. Give kudos to other ideas that you would like to see in a future version of Multisim!

The Multisim and Ultiboard R&D team is committed to reviewing every idea submitted via the Multisim and Ultiboard Idea Exchange. However, we cannot guarantee the implementation of any Multisim & Ultiboard Idea Exchange submission.

cancel
Showing results for 
Search instead for 
Did you mean: 
Post an idea

1. Increase Width of all traces together in the grapher.

2. Option to choose axis variables in the grapher, for example instead of time in the x-axis, I need some circuit voltage, for this option the simulator should simulate for all circuit variables, and after completion of simulation, the user could change the axis variables as desired. ( In PSPICE it happens the same way, and its useful)

3. When inductors are coupled using Inductor Coupling Block, then those inductors should be assigned dot polarity, same should also be done for the transformer models.

4. When I perform Transient, DC Sweep or Parameter Sweep analysis, all the selected output variables are plotted on the same graph, this is good for most of the times,
but sometimes I desire them to be plotted on 'Different Graph but on Same Graph Page' and I know this can be done by copying the original graph and paste it on the same page and then deselect the unwanted variables, which is tedious work. So there should be an additonal option to plot the variables on 'Different Graph but on Same Graph Page'. Also user should be able to change the bottom axis range of all graph together for easy comparision.

5. Is it possible to incoporate the datasheet of components within the multisim, without visiting manufacturer's webpage?

6. I desire the multisim to create backup of all custom setting made to it (for example Keyboard Shorcuts), so that I could restore it in case of new installation.

7. Multisim Viewer for viewing the schematics and simulating them

 

This seems to have become worse and worse in recent revisions of MS and UB.  When the spreadsheet is open on a net or part tab in UB or MS every time I touch a net or part or row in the spreadsheet it redraws the screens over and over and over for many many iterations before calming down.  At least 3 times but sometimes as many as maybe 10 or more times.  And it's not very fast either.  It is becoming VERY irritating.

0 Kudos

5. Schematic: To set some min and max limits for a voltage, current or power (they shall be visible in Grapher when you generate the plot). 

 

Notes:

This idea is splitted from topic "NI Multisim - new ideas" posted in 2014:

http://forums.ni.com/t5/Multisim-and-Ultiboard-Idea/NI-Multisim-new-ideas/idi-p/2792686

 

If some ideas are implemented in NI Circuit Design Suite 14 they shall be skipped and topic can be removed by admin.

0 Kudos

4. Schematic: To add operating state annotation for transistors (active, cutt-off, saturated).

 

Notes:

This idea is splitted from topic "NI Multisim - new ideas" posted in 2014:

http://forums.ni.com/t5/Multisim-and-Ultiboard-Idea/NI-Multisim-new-ideas/idi-p/2792686

 

If some ideas are implemented in NI Circuit Design Suite 14 they shall be skipped and topic can be removed by admin.

 

0 Kudos

3. Schematic: To add active probe (see CircuitMaker 2000 solution).

 

With the 14 version release there are probes feature added that I did not have a chance to evalute however probe can be moved dynamically to the specific net to check a signal level (voltage or current) or when you place on a component so power dissipation can be measured and showed (power dissipation vs time).

 

Notes:

This idea is splitted from topic "NI Multisim - new ideas" posted in 2014:

http://forums.ni.com/t5/Multisim-and-Ultiboard-Idea/NI-Multisim-new-ideas/idi-p/2792686

 

If some ideas are implemented in NI Circuit Design Suite 14 they shall be skipped and topic can be removed by admin.

0 Kudos

2. Schematic: To add power bias annotation for a components.

 

Notes:

This idea is splitted from topic "NI Multisim - new ideas" posted in 2014:

http://forums.ni.com/t5/Multisim-and-Ultiboard-Idea/NI-Multisim-new-ideas/idi-p/2792686

 

If some ideas are implemented in NI Circuit Design Suite 14 they shall be skipped and topic can be removed by admin.

0 Kudos

1. Schematic: To make an option to lock REFDES during copying circuit to the new sheet.

 

Notes:

This idea is splitted from topic "NI Multisim - new ideas" posted in 2014:

http://forums.ni.com/t5/Multisim-and-Ultiboard-Idea/NI-Multisim-new-ideas/idi-p/2792686

 

If some ideas are implemented in NI Circuit Design Suite 14 they shall be skipped and topic can be removed by admin.

  • Schematic Capture
0 Kudos

Recently in class we were using the Signal Generator and the Bode Plotter.  It made it somewhat difficult to get the correct readings because the live version does not include an option to place an open wire (was using it on an op amp) like in the application version.  It also made it somewhat difficult to change an AC current when involving different equations. Overall I like the Live version.

0 Kudos

 

This would make managing files in a project that much simpler.  As it is now you have to go into windows explorer, rename the file, go back to the toolbox, click on the file, navigate to and select the new file after it tells you it can't find the file anymore.

 

Just a right click/rename would be so much smoother.

  • Schematic Capture