
You are here:	NI Home > NI Developer Zone > NI Discussion Forums

Multifunction DAQ

Show: - -

Subject	Replies	Author	Kudos	Latest Post
multiplexing channels after the analog inputs of a DAQ Hardware	3	ENST	0	‎04-17-2003 12:58 PM by JustinBritten
How can i use the onboard memory from NI6534	1	Armandopoussito	0	‎04-16-2003 01:26 PM by JustinBritten
error 10843 on faster machine (OK on slow machine)	6	John McCulloch	0	‎04-16-2003 08:45 PM by John McCulloch
Why does the graph's amplitude increase with time when using multiple channels?	2	engineer 202	2	‎04-16-2003 03:22 PM by engineer 202
I am not able to set high and low limits for each channel seperately using LabWindows/CVI	1	aadesh	0	‎04-15-2003 01:11 PM by Russell
does driver for AT-MIO-16 in this website work with winXP?	1	song	0	‎04-15-2003 05:56 PM by Russell
My Data acquistion Scan locks up until I move the Mouse	2	Fridge	0	‎04-16-2003 06:35 AM by Fridge
What should i buy if i want to control a DC motor	1	ppl	0	‎04-16-2003 10:16 AM by Spencer S.
error information	1	Cheryl	0	‎04-16-2003 12:48 PM by JustinBritten
using virtual and physical channels at the same time	1	secmai	0	‎04-15-2003 02:08 PM by aasenjo
transfer sérial datas on digital I/O	1	steffdeloup	0	‎04-15-2003 01:55 PM by aasenjo
solution request	1	buckovski	1	‎04-14-2003 01:26 PM by Spencer S.
I need an equipment with an entry USB port to send a wav file and exit I & Q	1	carlos__12	0	‎04-14-2003 12:05 PM by RIO-Todd
Synchronization Techniques for Data Acquisition	1	Lotfi	0	‎04-11-2003 10:29 AM by Lotfi
Need to obtain the frequency of a voltage signal.	1	Foot	0	‎04-11-2003 11:59 AM by kroth
Does anyone have samples to replace WFM_from_disk functtion?	1	ramseng	0	‎04-11-2003 04:05 AM by Lotfi
necesito un equipo con una entrada del puerto usb(archivo.wav),y una salida I&Q	1	carlos__12	0	‎04-11-2003 04:36 PM by DiegoF
BufferOverrun error with DAQ_DB_Transfer in Visual C .NET at 100Hz sempling	1	iztok	0	‎04-11-2003 11:07 AM by JustinBritten
Why LV 6.1 and Nidaq 6.9.3 can't acquire low sampling rate and high frame size	1	Kusumah	0	‎04-11-2003 10:29 AM by JustinBritten
nonzero final value of triggered, buffered AO	1	sshoham	0	‎04-11-2003 10:21 AM by JustinBritten
High noise reception in my Pci-6013	1	zipizape	0	‎04-10-2003 10:35 AM by kroth
ECG Data Acquisition	1	Himanshu	0	‎04-10-2003 11:09 AM by JustinBritten
How can I do signal analysis on an analog signal obtained by a Labjack DAQ	1	Foot	0	‎04-09-2003 07:34 AM by Ben
I need an example vi about stepper motor control	1	Jee	0	‎03-10-2004 11:31 PM by MSE
how can i synchronize the data with PCI6534 in c++	3	Armandopoussito	0	‎04-14-2003 10:15 AM by JustinBritten
One of channel is hold at 5V ONLY when X>5V and Y<5V by dmm	2	Guppy	0	‎04-09-2003 08:49 PM by Guppy
XP/LabVIEW 4.0.1 Compatibility	2	rtsen	1	‎04-08-2003 10:49 AM by rtsen
Is it possible to output a voltage using the DAQ board?	1	Emily	0	‎04-07-2003 04:46 PM by kroth
Input floating at 100mV DC	1	Frustrated	0	‎04-07-2003 05:29 AM by Stefan S.
Is it possible to use PCI-1200 on the DAQ Signal Accessory?	1	sami	0	‎04-07-2003 02:39 PM by RamziH

Subject	Kudos
Re: USB 6211 bad data first few samples	2
Re: reverse motor direction	1
Re: Reduce the size of a file created by "write to waveform"	1
Re: install NIDAQmx Windows 7 64-bit	2
Re: Configuring Digital Output as High Impedance State (Tri-State)	1

User	Kudos Count
Henrik_Volkers	5
John_P1	4
crossrulz	2
Brad_K	2
Izzzzz	2

User	Tag Count
macaba	620
mtat76	90
JoeFriedchicken	73
Chris_D	68
John_P1	65



My Profile \| Privacy \| Legal \| Contact NI © 2011 National Instruments Corporation. All rights reserved. \| E-Mail this Page