
You are here:	NI Home > NI Developer Zone > NI Discussion Forums

Multifunction DAQ

Show: - -

Subject	Replies	Author	Kudos	Latest Post
a current source in parallel to AO voltage and both of them are connected to a resistor. Will it damage the AO pin?	3	JimSi	0	‎02-27-2013 12:34 PM by johnsold
AT-MIO16XE-10	4	gpachasg	0	‎02-27-2013 10:09 AM by gpachasg
In which pin(number) need to add thermocouple on DAQ CB-68LP ?	3	kodari	0	‎02-27-2013 09:05 AM by Dennis_Knutson
sbRIO 9636 serial examples	0	percy222	0	‎02-27-2013 08:56 AM by percy222
Will a PCI 6221 work in a 64 bit machine running XP?	5	rwbrook@integr…	0	‎02-27-2013 06:52 AM by rwbrook@integr…
USB-4432とSignal Expressについて	0	KH1031	0	‎02-27-2013 02:40 AM by KH1031
single board rio guide	4	percy222	0	‎02-26-2013 10:45 PM by percy222
single board rio run vi	2	percy222	0	‎02-26-2013 10:40 PM by percy222
Measuring the resistance, capacitance and inductance	4	flye2012	0	‎02-26-2013 07:39 PM by johnsold
Doubts about DAQmx MAX	3	AndreaCruz	1	‎02-26-2013 06:53 PM by Dennis_Knutson
USB-6216 intermittent zero voltage	3	dmorris	0	‎02-26-2013 06:29 PM by Kurt-P
NI 9214 won't measure multiple channels	1	nc61	0	‎02-26-2013 02:24 PM by CarmenC
USB-6212 6212 - Analog Output Stops! Doesn't Happen with NI9263	2	AMMA	0	‎02-26-2013 11:40 AM by AMMA
DAQ6024E to acquire miliVolts to covert to temp and pressure	6	Nikolian	0	‎02-26-2013 10:47 AM by JoelWhittC
PCI-4065 agonizingly slow	7	PaulG.	0	‎02-26-2013 10:43 AM by Steve_B
changing input range on ni usb6009 in matlab	1	gra3	0	‎02-26-2013 10:27 AM by Sev_K
ethernet daq on PC with 2 adapter boards	8	Ben_Engelen	1	‎02-26-2013 09:49 AM by ThiCop
sine wave generation using PCIe-6320	1	sbomy100	0	‎02-26-2013 08:41 AM by Dennis_Knutson
Overloaded Channels on NI PCI-4474 + accelerometer	1	giaulo	0	‎02-26-2013 07:04 AM by giaulo
Configuration DAQmx Input-task	2	Fred.Schimmel	1	‎02-26-2013 02:16 AM by Fred.Schimmel
Two edge measurement w PCIe-6320	2	Gary_MavSysInc	0	‎02-25-2013 07:54 PM by Gary_MavSysInc
NI-DAQmx tools Pallet not showing in LabView 6	4	Huck	0	‎02-25-2013 04:03 PM by Dennis_Knutson
Using Analog Input and Output at Once	0	Heeshung	0	‎02-25-2013 02:41 PM by Heeshung
Configuring multiple analog input using the DAQ assistant to run continuously	2	Stanhic	1	‎02-25-2013 11:29 AM by Stanhic
USB-6212	1	Ruiying	1	‎02-25-2013 09:53 AM by Dennis_Knutson
USB-6211 clocked DA generates error	1	mhubel	0	‎02-25-2013 09:26 AM by mhubel
high voltage differential measurement	4	Blane63580	0	‎02-25-2013 07:50 AM by Blane63580
Does a usb-powered DAQ has "real" isolation in power source for analog part?	5	fayx	0	‎02-24-2013 01:20 PM by Process_Systems
USB 6210 times out with 200284 on RHEL5 using nidaqmxbase 3.6 while trying to sample continuously. [ 1 2 3 4 ]	32	ase-tom	0	‎02-22-2013 04:47 PM by ase-tom
NI PCI 5152	1	hich1109	0	‎02-22-2013 10:39 AM by Tarek

Top Kudoed Posts

Subject	Kudos
Re: USB 6211 bad data first few samples	2
Re: Beginner question	1
Re: PCI-6143 - Tying inputs together	1
Re: Current Offset of 8uA on the Input USB-4431	1
Re: AO Spannung soll auf 0 wenn USB Verb. gekappt, wie Not-Halt	1

Top Kudoed Authors

User	Kudos Count
Henrik_Volkers	6
John_P1	4
Izzzzz	3
crossrulz	2
Brad_K	2

Top Taggers

User	Tag Count
macaba	620
mtat76	90
JoeFriedchicken	73
Chris_D	68
John_P1	65

By using this web site, you accept the Terms of Use for this web site. Please read these Terms of Use carefully before using any part of this site. Please go here for information on ni.com's copyright infringement policy.



My Profile \| Privacy \| Legal \| Contact NI © 2011 National Instruments Corporation. All rights reserved. \| E-Mail this Page