
You are here:	NI Home > NI Developer Zone > NI Discussion Forums

Multifunction DAQ

Show: - -

Subject	Replies	Author	Kudos	Latest Post
PID motor control with tach feedback	1	lhandte3	0	‎03-20-2013 12:31 PM by _Bryan
How can I use the 250kSps of the PCI-6221?	1	DavidBajzek	1	‎03-20-2013 12:08 PM by _Bryan
output sine wave with frequency and amplitude set by input	2	at_mars	0	‎03-20-2013 10:28 AM by at_mars
High frequency digital inputs to FPGA cannot be detected correct [ 1 2 ]	12	ccmkn	0	‎03-20-2013 10:11 AM by ccmkn
Sampling and FFTs	3	idt13	1	‎03-20-2013 09:47 AM by johnsold
Upgrading from PCI-6014 to PCI-6250 results in signal noise	0	CraigMcD	0	‎03-20-2013 08:01 AM by CraigMcD
Sporadic "error DAQmxWriteDigitalU32"	3	holwo	0	‎03-20-2013 04:51 AM by AndreasKr
PXI-6289 self calibration failed Error -200545	3	gaminn	0	‎03-20-2013 02:28 AM by prokyz
Wiring a 4 wire device to a NI 9208 Analog Input Card	3	Stanhic	1	‎03-19-2013 09:16 PM by Arham-H
Driver for NI 9233	1	ivibr8	0	‎03-19-2013 06:16 PM by KBreezy
Measuring flash intensity using a photodiode	7	joe25	1	‎03-19-2013 04:48 PM by johnsold
ni usb-6009 galvanic isolation	2	ljobe_CRO	0	‎03-19-2013 04:27 PM by johnsold
I am coding in C++ and I need help in understanding how to implement this code.	0	jesukiran	0	‎03-19-2013 10:09 AM by jesukiran
PMT voltage measurement	5	avi1812	0	‎03-19-2013 09:50 AM by johnsold
measuring resistance but value is not constant [ 1 2 ]	11	Zancis	2	‎03-19-2013 07:50 AM by crossrulz
terminal configuration ways	1	acewong7	0	‎03-18-2013 04:58 PM by fromm8
Add CJC channel for thermocouples	5	Nickerbocker	1	‎03-18-2013 02:54 PM by Nickerbocker
Logging large data using NI Daq	3	Easwar	1	‎03-18-2013 10:21 AM by Lukin
why has the acquisition of Signal from DAQ an error (breakpoint) in the time axis?	2	gyver.ning@gma…	0	‎03-18-2013 07:17 AM by Alex_Pi
USB-6008: in-line/serial connection of analog output channels?	2	rub1	0	‎03-18-2013 05:34 AM by rub1
NI cDAQ 9227 shunt resistor value	1	Stefan0012	0	‎03-18-2013 04:22 AM by SG3
USB 6343 XSeries Documentation for "DAQWriteNChanNSamp1DDigWfm"	1	StephanK.	0	‎03-18-2013 01:32 AM by StephanK.
What is the resolution for USB-6210 for positive input ranges?	2	Xichan	0	‎03-17-2013 11:57 PM by Xichan
how to measure angular position of motor using daq 6211	2	smritibhalehwar	0	‎03-17-2013 11:40 PM by smritibhalehwar
NI-Daq Legacy with Win 7, 32 bits	1	wg95070	0	‎03-17-2013 11:47 AM by Esteban.R
data acquisiton	7	fdfdf	0	‎03-16-2013 09:39 AM by Dennis_Knutson
Can I connect NI USB 6008 to thermocuples, pressure sensors and control valve	6	jackgrove	0	‎03-16-2013 12:33 AM by jackgrove
Can I use a reference trigger with a Linear Encoder Channel? (PCIe-6351)	3	EricSchwamb	0	‎03-15-2013 02:13 PM by James-K
USB 6363 AI Voltage Floating Up	1	kenkotz	1	‎03-15-2013 01:04 PM by johnsold
Simultaneous 4 Analog Output	1	marty33	0	‎03-15-2013 12:55 PM by johnsold

Top Kudoed Posts

Subject	Kudos
Re: USB 6211 bad data first few samples	2
Re: reverse motor direction	1
Re: Reduce the size of a file created by "write to waveform"	1
Re: install NIDAQmx Windows 7 64-bit	2
Re: Configuring Digital Output as High Impedance State (Tri-State)	1

Top Kudoed Authors

User	Kudos Count
Henrik_Volkers	5
John_P1	4
crossrulz	2
Brad_K	2
Izzzzz	2

Top Taggers

User	Tag Count
macaba	620
mtat76	90
JoeFriedchicken	73
Chris_D	68
John_P1	65

By using this web site, you accept the Terms of Use for this web site. Please read these Terms of Use carefully before using any part of this site. Please go here for information on ni.com's copyright infringement policy.



My Profile \| Privacy \| Legal \| Contact NI © 2011 National Instruments Corporation. All rights reserved. \| E-Mail this Page