
You are here:	NI Home > NI Developer Zone > NI Discussion Forums

Multifunction DAQ

Show: - -

Subject	Replies	Author	Kudos	Latest Post
Have an idea for new DAQ hardware or new DAQ software features?	0	JordanG	0	‎05-29-2012 03:31 PM by JordanG
Is this the best way to measure several voltages from a single task?	1	dav2010	0	‎05-25-2013 07:19 AM by crossrulz
Is is a proper way to solve the problem of high common-mode voltage? [ 1 2 3 ]	26	xcuresme	1	‎05-24-2013 09:10 PM by xcuresme
Connecting USB-6211 to Ubuntu 12.04 with Linux Kernel 3.5	2	me1234	0	‎05-24-2013 02:17 PM by me1234
AO Spannung soll auf 0 wenn USB Verb. gekappt, wie Not-Halt	6	P3lzi	2	‎05-24-2013 05:24 AM by P3lzi
overheating	2	qcl123	0	‎05-24-2013 12:29 AM by qcl123
Looking into replacing an Arduino Uno unit with a USB 6009 for timing delay solution	1	cvamos	0	‎05-23-2013 09:12 PM by johnsold
Analog Output not staying at programmed level SetAOIdleOutputBehavior vs. Buffer size	2	kbill79	0	‎05-23-2013 05:23 PM by John_P1
NI 6255 accuracy calculations	1	JLAnderson	0	‎05-23-2013 03:10 PM by Jason-M
Error-88302	5	ilublessing	0	‎05-23-2013 08:20 AM by Chris_J
Can floating a signal be a proper way to solve the problem of high common-mode voltage?	4	xcuresme	0	‎05-22-2013 09:16 PM by xcuresme
Thermocouples randomly stop working, then start again with SCXI 1102	3	BBalmforth	0	‎05-22-2013 05:05 PM by Travis-E
Beginner question [ 1 2 ]	17	Jango	1	‎05-22-2013 02:52 PM by Jango
daq assistant	4	lupo88	1	‎05-22-2013 10:30 AM by FatBoyMonchi
McAfee causes DAQ misread	1	verdmonte	0	‎05-22-2013 10:22 AM by BluesKnight
1MS/s/ch Simulltaneously sampled, Single Ended Analogue Voltage measuremnt DAQ	3	sm81	0	‎05-22-2013 08:14 AM by Izzzzz
Accuracy of NI Card (NI 9208) = expanded uncertainty(2 sigma)?	1	VMacl	0	‎05-22-2013 05:03 AM by prokyz
Clarification and Confirmation About the Practical Implications of Common Mode Voltage on Differential Measurements	8	chassan	2	‎05-22-2013 04:23 AM by xcuresme
How to wire a Fluid Components International ST75 flow meter to DAQ System?	1	BBalmforth	0	‎05-21-2013 04:52 PM by AnalogKid2Digi…
General DAQ adquisition program, read and save in a file	8	ATO	0	‎05-21-2013 11:02 AM by ATO
i am looking for MSI Blast a utility to remove NI DAQ drivers [ 1 2 ]	11	don7	2	‎05-21-2013 10:24 AM by Andy-C
Thermocouple readings fluctuating JType	3	sonotk	0	‎05-21-2013 09:22 AM by Henrik_Volkers
Can I drive a stepper motor via DAQPad6020E??	1	REZA1360	0	‎05-21-2013 08:11 AM by dshusker
Windows 7 vs XP PCI bus problems	5	SmokeMonster	0	‎05-21-2013 07:26 AM by dshusker
PCI 6110	2	dev_digilogic	0	‎05-21-2013 06:44 AM by dls1
nidaqmx DIO high & low	1	aderogba	0	‎05-20-2013 06:37 PM by BluesKnight
How to change analog output rising edge and falling edge.	1	Zhi	0	‎05-20-2013 01:24 PM by BluesKnight
my daq	1	sfstolf	0	‎05-20-2013 12:31 PM by Plínio
cRIO	1	Rez8	0	‎05-20-2013 11:48 AM by hicksc
What is input equivalent circuit of USB 6009 PFI0	2	kscholl	0	‎05-20-2013 09:25 AM by kscholl
Filtering out common mode signals with a transformer for a DAQ.	4	BigC	0	‎05-20-2013 02:38 AM by xcuresme

Subject	Kudos
Re: USB 6211 bad data first few samples	2
Re: Pressure Sensor Ground Loop Problem	1
Re: Having trouble setting up Daqmx in WIndows 7	1
Re: Synching AO and Counter Output, arming-and-triggering sequence of events	6
Re: NI 6221 37 PIN Analog Input problem	1

User	Tag Count
macaba	620
mtat76	90
JoeFriedchicken	73
Chris_D	68
John_P1	65



My Profile \| Privacy \| Legal \| Contact NI © 2011 National Instruments Corporation. All rights reserved. \| E-Mail this Page