
You are here:	NI Home > NI Developer Zone > NI Discussion Forums

Motion Control and Motor Drives

Show: - -

Subject	Replies	Author	Kudos	Latest Post
NI-9514 with external absolute encoder	3	Jabba	0	‎02-12-2013 06:21 PM by PaulRB
store generating numbers as 2D arrays	7	OpticHero	2	‎02-11-2013 09:24 AM by Edwin_Wise
Control P7000 through serial port	2	galanm	1	‎02-07-2013 12:02 PM by galanm
CompactDAQ and P70360	1	Shazlan	0	‎02-04-2013 02:34 PM by galanm
Change gearing sign (reverse slave axis)	2	Emme	0	‎01-30-2013 09:22 AM by Edwin_Wise
Soft Motion Runtime Error	3	Banjo_B	0	‎01-30-2013 08:58 AM by Banjo_B
Measurement & Automation中通过PCI7344驱动三菱电机，电机无法达到额定的速度	0	luckygyy	0	‎01-29-2013 11:57 PM by luckygyy
pci versus pxi versus compactRIO	1	dg_lbe	0	‎01-29-2013 04:38 PM by The_Hunt
Solar Tracker sensor daq	1	43431	0	‎01-28-2013 02:29 PM by Blake-C
pci-7332 board execution is slow	3	dg_lbe	1	‎01-28-2013 10:42 AM by LVbum42
Control DaNI robot	6	abojojo	0	‎01-24-2013 02:58 PM by CMal
Controlling XY stage connected to parallel port using labview	1	srms	0	‎01-23-2013 09:26 AM by Burrito
read encoder finishing late above 100 hz	0	NEILBH	0	‎01-23-2013 05:39 AM by NEILBH
stepper drive 9501 example?	1	SaraBaber	0	‎01-22-2013 07:52 AM by ShalimarA
how to set x-axis of waveform chart to be real time	0	premananda	0	‎01-21-2013 02:10 AM by premananda
Querying the SoftMotion table size programmatically	4	JKSH	0	‎01-20-2013 06:34 PM by JKSH
Building a simple shutter - beginner question	5	david.eisenberg	0	‎01-19-2013 08:47 PM by david.eisenberg
analog input issue with the pci-7332 and umi-7774 [ 1 2 ]	10	dg_lbe	0	‎01-19-2013 03:00 PM by dg_lbe
softmotion module using 9505?	6	SaraBaber	0	‎01-18-2013 08:02 AM by Marshall_B
NI Motion with 3rd party cnc controller	1	Gharb	0	‎01-17-2013 03:39 PM by LVbum42
2011 9501 C-Series Example broken wire/property	5	wandering397	0	‎01-17-2013 10:27 AM by The_Hunt
Softmotion and NI-950X Module Compatibility	7	dwjef	2	‎01-16-2013 05:37 PM by Simon-P
User-Defined Variables, FPGA mode, and SoftMotion 2012 + NI 9505	2	JKSH	1	‎01-16-2013 04:03 PM by Aix-La-Chapelle
Attempt to communicate to Newport MM4006 controllers via serial in new labview	2	A.Obey	0	‎01-15-2013 03:54 AM by A.Obey
How does SoftMotion recognize an Axis in an EtherCAT XML?	7	MarkusJ	0	‎01-10-2013 11:06 PM by David-n-MO
Labview system identification	1	AvinashBPAI	0	‎01-07-2013 06:45 PM by AndyClegg
Third party ethercat motion controllers	6	maherhome	0	‎12-30-2012 12:42 PM by maherhome
"Distributed motion control'	2	W.P.	0	‎12-27-2012 09:49 AM by W.P.
synchronize NI 9514 with NI 9401 for digital output	2	italo.franchini	0	‎12-17-2012 06:00 PM by italo.franchini
Running N31HRHJ Motor on PXI 7330 and UMI 7772	8	TheXDestroyer	1	‎12-17-2012 09:43 AM by TheXDestroyer